老化测试设备

咨询热线

18566398802
首页 > 标准大全 > ASTM D4434标准详情
相关测试仪器

ASTM D4434

  本页面标准信息均来源于网络收集,或由参与标准制定的供应商提供,只作为参考使用。我们愿意和您交流ASTM D4434标准细节信息或ASTM D4434测试方法,欢迎致电【18566398802】

ASTM D4434标准介绍

        聚氯乙烯屋面薄板的标准规范:

本规范规定了拟用于单层屋顶薄膜的、用聚氯乙烯树脂作为初级聚合物而制造的柔性薄板空气暴露测试程序。

Q-sun氙灯试验箱ASTM D4434测试方法 

ASTM D4434测试方法

ASTM D4434英文简介

This specification covers flexible fiber- or fabric-reinforced sheet made from poly(vinyl chloride) resin as the primary polymer intended for use in single-ply roofing membranes exposed to the weather. The sheet shall contain. In-place roof system design criteria such as fire resistance, material compatibility, wind uplift resistance, in-situ shrinkage, among others, are beyond the scope of this specification. The physical requirements for which the sheet materials shall be tested on and shall conform accordingly to are as follows: overall thickness and thickness over scrim; tensile strength at break; breaking strength; elongation at break; seam strength; retention of properties after heat aging; tear resistance and tearing strength; low temperature bend; cracking and crazing after accelerated weathering test; linear dimensional change; change in weight after immersion in water; and static and dynamic puncture resistance.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification covers flexible sheet made from poly(vinyl chloride) resin as the primary polymer intended for use in single-ply roofing membranes exposed to the weather. The sheet shall contain reinforcing fibers or reinforcing fabrics.

1.2 The tests and property limits used to characterize the sheet are values intended to ensure minimum quality for the intended purpose. In-place roof system design criteria, such as fire resistance, material compatibility, wind uplift resistance, in-situ shrinkage, among others, are factors that must be considered but are beyond the scope of this specification.

1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitation prior to use.

2. Referenced Documents (purchase separately)

ASTM Standards

D570 Test Method for Water Absorption of Plastics

D638 Test Method for Tensile Properties of Plastics

D751 Test Methods for Coated Fabrics

D1004 Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting

D1204 Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature

D2136 Test Method for Coated Fabrics--Low-Temperature Bend Test

D3045 Practice for Heat Aging of Plastics Without Load

D5602 Test Method for Static Puncture Resistance of Roofing Membrane Specimens

D5635 Test Method for Dynamic Puncture Resistance of Roofing Membrane Specimens

D7635/D7635M Test Method for Measurement of Thickness of Coatings Over Fabric Reinforcement

G151 Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources

G154 Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials

G155 Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials

温馨提醒:本ASTM D4434可能存在更新的版本,建议寻找ASTM D4434的发行商确认。

符合 ASTM D4434 标准的
老化试验箱

  • 氙灯加速老化试验箱图片 氙灯加速老化试验箱氙灯加速老化试验箱

    Q-sun Xe-1-BCE氙灯加速老化试验箱配有全光谱氙弧灯、太阳眼辐照度控制系统,该型号的氙灯加速老化试验箱同时具有背部喷功能。

    Q-sun Xe-1-BCE 马上询价
  • 氙灯老化试验机图片 氙灯老化试验机氙灯老化试验机

    Q-SUN Xe-3-HCE是一款具有全光谱光照模拟、湿度控制以及制冷功能的氙灯老化试验机,其命名规则为湿度控制(H)、制冷功能(C)。

    Q-SUN Xe-3-HCE 马上询价
  • 紫外老化试验箱图片 紫外老化试验箱紫外老化试验箱

    QUV/spray紫外老化试验箱具有水喷淋及辐照度自动校准功能,可更真实的还原紫外光照环境下,产品的老化情况。

    QUV/spray 马上询价
  • 氙灯耐候试验箱图片 氙灯耐候试验箱氙灯耐候试验箱

    Q-SUN Xe-3-HSCE氙灯耐候试验箱同时具有湿度控制、喷淋以及制冷功能,其命名规则为湿度(H)、喷淋(S)、制冷(C)。

    Q-SUN Xe-3-HSCE 马上询价
近期文章